photo

MULI


Last seen: 9 days ago |  Active since 2024

Followers: 1   Following: 0

Statistics

  • Knowledgeable Level 2
  • 3 Month Streak
  • First Answer

View badges

Feeds

View by

Answered
problems encountered in DDPG.
Hi 邓龙京, The error message “Number of input layers for state-action-value function deep neural network must equal the number of...

9 days ago | 0

Answered
Error in rl.agent.AbstractAgent/train while executing example "Train Reinforcement Learning Agent in MDP Environment"
Hi @David Carrasco Martínez, I understand that you are facing an issue when “doTraining” flag is set to “true” in "Train Reinf...

9 days ago | 0

Answered
Train a DQN Agent: RL Simulink with Simscape (Error: Discontinuities detected within algebraic loop)
Hello, I understand that you are trying to replace a PI controller with a DQN agent for your Buck Converter model and encounte...

12 days ago | 0

Answered
get error runing TrainTD3AgentForPMSMControlExample.mlx
Hi @hai hu, I understand that you are facing an issue in the "TrainTD3AgentForPMSMControl" example model when “doTraining” fla...

13 days ago | 0

Answered
I am finding it difficult to design a 50MW VSC PV inverter.
Hi Prithwi, I understand that you are facing an issue in obtaining the desired output power. You can try the below suggestions...

14 days ago | 0

Answered
Error in solver configuration
Hi Pranjali, The error message "Input voltage must be greater than or equal to zero" suggests that your DC-DC converter is rec...

14 days ago | 0

Answered
Simscape Electrical: access "Display Assosciated Initial Conditions" programmatically
Hi Fredrik, To automatically set initial conditions for multiple synchronous machines using load flow results, you can follow ...

14 days ago | 0

Answered
Simulink stepper motor control
Hi Zsombor, To achieve continuous motor control independent of Simulink's sample time, you can use hardware interrupts or time...

16 days ago | 0

Answered
how can we plot the voltage trajectory of pmsm motor , when we have vd and vq data from simulink?What kind of plot is this?
Hi Deepak, To plot the voltage trajectory of a Permanent Magnet Synchronous Motor (PMSM) using the data from Simulink, you ...

16 days ago | 0

Answered
How to change SPWM Frequency of Arduino mega 2560 with MATLAB SIMULINK
Hi yahya, The output pulses from your Simulink model appears to be generated with frequency of "sin wave" so this is why the a...

19 days ago | 0

Answered
Simulink model control servo by mpu9250
Hi Aseel, To control servo motor using one of the yaw, pitch, or roll angles derived from your MPU9250 sensor in Simulink, you...

19 days ago | 0

Answered
PSCAD, Matlab interfacing
Hi Mohamed, To synchronize the timing of your MATLAB script with the PSCAD simulation, you need to ensure that your MATLAB cod...

19 days ago | 0

Answered
What is the best method to model or utilize the built-in model for a three-phase voltage regulator in MATLAB Simulink, specifically for the IEEE 34 distribution network?
Hi Asi, To model a three-phase voltage regulator in MATLAB Simulink for the IEEE 34 distribution network and with load flow an...

20 days ago | 0

Answered
detect and remove motion artifacts from ppg signal using lms adaptive filter
Hi Rajesh, I understand that you are looking for a method to remove noise from motion artifacts in a PPG signal. You can fol...

21 days ago | 0

Answered
Failed to load OpenDRIVE data: Failed to convert '-'
Hi, It looks like you are facing an error because there is an invalid character, like '-' where a number should be, in your fi...

21 days ago | 0

Answered
How to connect simpowersystem generic battery block to the simscape blocks without an algebraic loop error?
Hi Yurdakul, I understand that you are trying to connect a SimPowerSystems battery block to Simscape components and faci...

21 days ago | 0

Answered
Synchronous machine model incorrectly initializes when taking into account saturation
Hi Solis, I understand that you are facing an issue with the initialization of a synchronous machine model when accounting for...

1 month ago | 1

| accepted

Answered
how can i account charge and discharge of battery in ev modeling.
Hi Gokarna, I understand that you are trying to model both the charge and discharge behaviour of a battery in an electric vehi...

1 month ago | 0

Answered
C2000 simulink reduces PWM frequency
Hi Hadia, I understand that you are experiencing an issue where PWM signal is expected to generate at frequency of 20kHz but o...

1 month ago | 0

Answered
Failed to read "n" uint8 value(s) from the device error while reading serial information.
Hi Andrew, I understand that you are experiencing intermittent errors when trying to read data from a scale via an RS232 conne...

1 month ago | 0

Answered
Saturation in Synchronous Machine Salient Pole
Hi Jakob, I understand that you are facing an issue related to the configuration of the saturation curve in a salient pole syn...

1 month ago | 0

Answered
ACD block for C2000 MCU doesn't follow the sampletime we have set
Hi Henrik, I understand that you are facing an issue with the ADC block on the F280025C LaunchPad. Despite setting a sample t...

1 month ago | 0

Answered
How can I obtain the negative sequence currents and voltages in the d and q axises for inverter control?
Hi Fater, I understand that when you are using a negative angle for abc to dqo transformation you are getting 2nd order harmon...

1 month ago | 0

Answered
Simulation of three-phase ferroresonances in Simulink Simscape Electrical - Specialized Power Systems
Hello Torben, I understand that you need to simulate three-phase ferroresonance in an electrical power supply network using S...

1 month ago | 0

| accepted

Answered
How to use parfor for access or link function of satellite communication?
Hi Ravi, I understand that you are facing an error where nodes belong to different ‘satelliteScenarios’ while using a ‘parfor’ ...

1 month ago | 0

Answered
Real-time control PLC connected to Simulink is faulty
Hi Hoang, It seems like the issue you are facing arises from the mismatch between the sampling rates of your system component...

2 months ago | 0

Answered
How to use Battery Pulse Analysis with both Discharge and Charge Pulses?
Hi Christopher, I understand that you are trying to analyse a dataset that includes both charge and discharge pulses, and you...

2 months ago | 0

Answered
NI9401 Pulse Generation and Digital Output same time
Hi Tugrul, I understand that you need to control a stepper motor using a TRINAMICS stepper controller with the NI 9401 module ...

2 months ago | 0

Answered
Can somebody help me to read data from the register using the TI I2C receive block (part of Embedded Coder Support Package for Texas Instruments C2000 Processors)
I understand that you are facing an issue in reading data from the LSM6DS3H inertial module using the TMS320F28035 Piccolo Micro...

2 months ago | 0

Answered
Issue with Serial Receive (Arduino Hardware) SIMULINK interfacing with Arduino Mega. "255"
Hi John, I understand that you are sending data from a computer to an Arduino Mega using a USB-to-TTL adapter. The data should...

2 months ago | 0

Load more