![photo](/responsive_image/150/150/0/0/0/cache/matlabcentral/profiles/1151042_1607426602031.jpg)
Torsten Knodt
A123 Systems GmbH
Followers: 0 Following: 0
Professional Interests: Rapid Prototyping, Ground Vehicle Physical Simulation, Virtual Integration, Model Based Development, AutoSAR, Symbolic Solutions to Differential Equations, Static and Dynamic Parameter Estimation
Statistics
RANK
4,297
of 292,713
REPUTATION
12
CONTRIBUTIONS
9 Questions
3 Answers
ANSWER ACCEPTANCE
44.44%
VOTES RECEIVED
2
RANK
of 19,933
REPUTATION
N/A
AVERAGE RATING
0.00
CONTRIBUTIONS
0 Files
DOWNLOADS
0
ALL TIME DOWNLOADS
0
CONTRIBUTIONS
0 Posts
CONTRIBUTIONS
0 Public Channels
AVERAGE RATING
CONTRIBUTIONS
0 Highlights
AVERAGE NO. OF LIKES
Feeds
Question
How to continuously repeat the output of the "From Spreadsheet" source block?
Hi, How can I continuously repeat the output of the "From Spreadsheet" source block? The extrapolation at the end does not pro...
4 years ago | 1 answer | 0
1
answerQuestion
How can I draw a mesh into a block mask/ icon?
Hello, I have a masked Simulink block. Now I want to draw a mesh into the icon. Unfortunately the mesh is drawn into an own w...
7 years ago | 1 answer | 0
1
answerAutomotive problem - Counting and saving
This depends on your interface to write to the EEPROM. Normally you would count in your RAM and trigger writing to the EEPROM in...
8 years ago | 0
How can i change a value of a resistor during simulation using simpowersystems toolbox ( R L C branch )
I had the same requirement. I either use a voltage measurement together with a controlled current source or a current measureme...
8 years ago | 0
| accepted
Question
/usr/bin/ld: raccel_sfcn_utils.o: undefined reference to symbol 'dlclose@@GLIBC_2.2.5'
I get the following message when starting a simulation in rapid acceleration mode under Ubuntu Xenial 64 Bit which works under W...
8 years ago | 0 answers | 0
0
answersQuestion
What is the cause of the error message "FIMATH mismatch:Property 'ProductWordLength'" here?
I get the error message FIMATH mismatch:Property 'ProductWordLength': 16 ~= 32 from the following action code in a stat...
8 years ago | 0 answers | 0
0
answersHow to define the sampling time in a system of Simscape Power System Blocks without accuracy lost importants?
Hi Tony, it's hard to give an advice without knowing your model, simulation settings and the intent of your simulation. Becaus...
8 years ago | 0
| accepted
Question
OutOfMemoryError when building PDF System Design Description for "big" Simulink Model
Hello, I get an OutOfMemoryError when building a System Design Description in PDF and Word format. I already increased the heap...
8 years ago | 0 answers | 0
0
answersQuestion
Initial output value for bus in enabled subsystem hierarchy
I have a hierarchy of subsystems where a middle subsystem is an enabled one. The hierarchical subsystems each have a single outp...
9 years ago | 1 answer | 0
1
answerQuestion
Analyzing and creating fixed-point data types.
Hello, is there a single function to get the minimum and maximum value representable by a specific fixed-point data type? I am ...
11 years ago | 1 answer | 0
1
answerQuestion
Simulink message "Attempt to use invalid data type id 17"
Hello, how can I find out which data type corresponds to a specific id when getting the message "Attempt to use invalid data ty...
12 years ago | 1 answer | 2
1
answerQuestion
"Variable time delay" block in "For Each Subsystem"
Hello, I try to synthesize noise coming from multiple targets to multiple sensors. I have two cascaded for-each sub-systems, th...
12 years ago | 1 answer | 0