photo

Sudarshan


Last seen: 17 days ago |  Active since 2017

Followers: 0   Following: 0

Message

Statistics

All
  • Personal Best Downloads Level 2
  • First Submission
  • Explorer
  • Thankful Level 2
  • Thankful Level 1

View badges

Feeds

View by

Submitted


Power Factor Correction (PFC) Boost Converter
PFC Boost Converter

12 months ago | 21 downloads |

Thumbnail

Question


Power Supply current output for data analysis
Hello, We have many power supplies that have been running for the past 15 years. I have access to the power supply output curre...

2 years ago | 1 answer | 0

1

answer

Question


Importing data from a .mat file into the Sensitivity Analyzer App on Simulink
I have a .mat file that has data that I would like to import into the Sensitivity Analyzer app on simulink to perform additional...

2 years ago | 1 answer | 0

1

answer

Question


Capturing efficiency of a system while sweeping voltages and duty cycle parameters
I have a simscape simulation model of a power electronics converter and I need to find the optimum parameters to achieve the bes...

2 years ago | 1 answer | 0

1

answer

Question


Modeling RG220 coaxial cable using a PI section line
I have two parallel RG-220/u coaxial cables which go to a magnet load from a pulse forming network. I recently found out that I ...

2 years ago | 1 answer | 0

1

answer

Question


Extracting amplitude and frequency component using short time Fourier transform
I need to calculate the capacitance and equivalent series resistance (ESR) of a capacitor in a Boost converter. My boost convert...

2 years ago | 1 answer | 0

1

answer

Question


Three-phase, three-winding transformer parameters
How to calculate the following values in a three-phase, three-winding transformer? I need to model this transformer in MATLAB/Si...

2 years ago | 1 answer | 0

1

answer

Question


How to create a square wave with different amplitudes?
I need to generate a square wave from -8 to 15 with a frequency of 18 kHz. How can I do this in Simulink?

2 years ago | 1 answer | 0

1

answer

Question


RC snubbers for 12-pulse thyristor bridge
I am trying to simulate an AC-DC power supply (12-pulse thyristor bridge connected in series) with an RC snubber. The real power...

3 years ago | 0 answers | 0

0

answers

Question


Step Down Solar PV High DC Voltage
I have a PV panel which is rated at 5HP. The DC voltage generated by the panel is connected to the DC bus of its respective AC d...

4 years ago | 0 answers | 0

0

answers

Question


Computing voltage and current amplitude and average power
Hello, I have three sinusoidal waveforms namely, voltage, current, and power acquired using an oscilloscope which I then have c...

4 years ago | 1 answer | 0

1

answer

Question


How to model a Klystron in Matlab/Simulink?
Hello all, I am trying to model a Klystron which is a specialized linear-beam vacuum tube that is used as an amplifier for high...

5 years ago | 0 answers | 0

0

answers

Question


How should the change in delta V (change in voltage) look like in a perturb and observe algorithm?
Hello all, I am currently working on an IEEE paper which is about extracting maximum power under partial shading of PV panels...

6 years ago | 0 answers | 0

0

answers

Question


How do I plot this graph on MATLAB?
Dear all, I am having difficulty in plotting this particular graph on MATLAB. I know that I am supposed to use an if and/or f...

6 years ago | 1 answer | 0

1

answer

Question


How to create a Network Node Incidence Matrix?
Hello guys, I am currently working on an IEEE paper which uses the Data of an IEEE-24 Bus System. I need to construct a Network...

7 years ago | 2 answers | 0

2

answers

Question


How to reduce the size of a 144x1 Vector to a 72x1 Vector by adding two consecutive elements in the Original Vector?
Hello all, I have a vector which has the dimensions of 144x1. The numbers in the vector repeat after every sixth row. For examp...

7 years ago | 1 answer | 0

1

answer