wlanEHTSIGUserBitRecover

Recover user field bits in EHT-SIG field

Since R2023b

Syntax

[bits,failCRC,cfgUpdated] = wlanEHTSIGUserBitRecover(sym,nVar,cfg)

[bits,failCRC,cfgUpdated] = wlanEHTSIGUserBitRecover(sym,nVar,csi,cfg)

[bits,failCRC] = wlanEHTSIGUserBitRecover(___)

Description

[bits,failCRC,cfgUpdated] = wlanEHTSIGUserBitRecover(sym,nVar,cfg) recovers bits, the EHT-SIG user field bits in an IEEE^® 802.11be™ extremely high-throughput multi-user (EHT MU) OFDMA or non-OFDMA transmission.

The function recovers bits from sym, the demodulated and equalized EHT-SIG field symbols. The cfg input parameterizes the transmission, which is subject to channel noise with estimated variance nVar.

The function also returns failCRC, the result of the cyclic redundancy check, and cfgUpdated, the updated transmission parameters recovered from the decoded EHT-SIG user field. If you use this syntax and the function cannot interpret the recovered bits, the function does not return an output and issues an error message.

For more information on 802.11be signal recovery, see the Recovery Procedure for an 802.11be Packet example.

[bits,failCRC,cfgUpdated] = wlanEHTSIGUserBitRecover(sym,nVar,csi,cfg) also enhances the demapping of OFDM subcarriers by using channel state information csi.

[bits,failCRC] = wlanEHTSIGUserBitRecover(___) returns an output without issuing an error message if the function cannot interpret the recovered bits. You can use this syntax with either input argument combination from the first two syntaxes.

Examples

Recover EHT-SIG Field Bits with Channel State Information

Create an EHT MU configuration object with a channel bandwidth of 20 MHz.

cfgEHT = wlanEHTMUConfig("CBW20");
chanBW = cfgEHT.ChannelBandwidth;

Generate a time-domain waveform for the configuration, assuming a channel with no impairments.

tx = wlanWaveformGenerator([1;0],cfgEHT);
rx = tx;
nVar = 0;

Get the WLAN field indices for the configuration.

ind = wlanFieldIndices(cfgEHT);

Create an EHT recovery configuration object with a channel bandwidth of 20 MHz.

cfg = wlanEHTRecoveryConfig(ChannelBandwidth=chanBW);

Isolate the part of the waveform that corresponds to the L-SIG field. Demodulate and decode the L-SIG field. Set the LSIGLength property of the recovery object.

rxLSIG= rx(ind.LSIG(1):ind.LSIG(2),:);
lsigDemod = wlanEHTDemodulate(rxLSIG,"EHT-SIG",cfg);
info = wlanEHTOFDMInfo("L-SIG",cfg);
lsigDemod = lsigDemod(info.DataIndices,:);
[~,~,lsigInfo] = wlanLSIGBitRecover(lsigDemod,nVar);
cfg.LSIGLength = lsigInfo.Length;

Isolate the part of the waveform that corresponds to the U-SIG field. Demodulate and decode the U-SIG field. Update the recovery object with the U-SIG bits.

rxUSIG = rx(ind.USIG(1):ind.USIG(2),:);
usigDemod = wlanEHTDemodulate(rxUSIG,"U-SIG",cfg);
usigDemod = usigDemod(info.DataIndices,:);
[usigBits,failCRC] = wlanUSIGBitRecover(usigDemod,nVar);
cfg = interpretUSIGBits(cfg,usigBits,failCRC);

Isolate the part of the waveform that corresponds to the EHT-SIG field and demodulate it.

rxEHTSIG = rx(ind.EHTSIG(1):ind.EHTSIG(2),:);
ehtsigDemod = wlanEHTDemodulate(rxEHTSIG,"EHT-SIG",cfg);

Isolate the data indices and specify channel state information.

sym = ehtsigDemod(info.DataIndices,:,:);
csi = ones(52,1);

Recover the EHT-SIG common field bits using the channel state information. Display the result of the cyclic redundancy check.

[bits,failCRC] = wlanEHTSIGCommonBitRecover(sym,nVar,csi,cfg);
disp(failCRC);

   0

Update the recovery object with the common field bits.

cfg = interpretEHTSIGCommonBits(cfg,bits,failCRC);

Recover the EHT-SIG user field bits and update the recovery object with them. Display the updated object.

[bits,failCRC,cfgUpdated] = wlanEHTSIGUserBitRecover(sym,nVar,csi,cfg);
disp(cfgUpdated{1});

  wlanEHTRecoveryConfig with properties:

                ChannelBandwidth: 'CBW20'
                      LSIGLength: 123
                 CompressionMode: 1
                       EHTSIGMCS: 0
        NumEHTSIGSymbolsSignaled: 2
                 LDPCExtraSymbol: 1
             PreFECPaddingFactor: 1
                  PEDisambiguity: 0
                   GuardInterval: 3.2000
                      EHTLTFType: 4
                NumEHTLTFSymbols: 1
                UplinkIndication: 0
                        BSSColor: 0
                    SpatialReuse: 0
                    TXOPDuration: -1
                NumNonOFDMAUsers: 1
       NumUsersPerContentChannel: 1
         RUTotalSpaceTimeStreams: 1
                          RUSize: 242
                         RUIndex: 1
      PuncturedChannelFieldValue: 0
                           STAID: 0
                             MCS: 0
                   ChannelCoding: ldpc
                     Beamforming: 0
             NumSpaceTimeStreams: 1
    SpaceTimeStreamStartingIndex: 1

   Read-only properties:
                        PPDUType: su
                      EHTDUPMode: 0

Recover EHT-Data Field from EHT SU Transmission

Generate EHT SU Waveform

Create a single-user EHT configuration object with a channel bandwidth of 320 MHz.

chanBW = "CBW320";
cfgEHTSU = wlanEHTMUConfig(chanBW);

Create an EHT recovery object with the same channel bandwidth.

cfg = wlanEHTRecoveryConfig(ChannelBandwidth=chanBW);

Create a sequence of data bits. Use the bits to generate a time-domain waveform for the specified configuration. Pass the waveform through an AWGN channel with a signal-to-noise ratio of 10 dB. Return the PPDU field indices.

bits = randi([0 1],8*psduLength(cfgEHTSU),1);
tx = wlanWaveformGenerator(bits,cfgEHTSU);
rx = awgn(tx,10);
ind = wlanFieldIndices(cfg);

Recover L-SIG Bits

Demodulate the L-LTF and estimate the channel. Using the demodulated symbols, estimate the noise power.

lltf = rx(ind.LLTF(1):ind.LLTF(2),:);
lltfDemod = wlanEHTDemodulate(lltf,"L-LTF",cfg);
lltfChanEst = wlanLLTFChannelEstimate(lltfDemod,chanBW);
nVar = wlanLLTFNoiseEstimate(lltfDemod);

Decode the L-SIG field and obtain the OFDM information. The recovery configuration object requires this information to obtain the L-SIG length.

lsig = rx(ind.LSIG(1):ind.LSIG(2));
lsigDemod = wlanEHTDemodulate(lsig,"L-SIG",cfg);
info = wlanEHTOFDMInfo("L-SIG",cfg);
lsigDemodData = lsigDemod(info.DataIndices,:);

Estimate the channel at the L-SIG field and equalize the L-SIG symbols.

preEHTChanEst = wlanPreEHTChannelEstimate(lsigDemod,lltfChanEst,chanBW);
lsigEq = wlanEHTEqualize(lsigDemodData,preEHTChanEst(info.DataIndices,:),nVar,cfg,"L-SIG");

Recover the L-SIG bits and set the L-SIG length of the recovery object.

[lsigBits,failCheck,lsigInfo] = wlanLSIGBitRecover(lsigEq,0);
cfg.LSIGLength = lsigInfo.Length;

Update Recovery Configuration Object with U-SIG Bits

Demodulate the U-SIG field.

usig = rx(ind.USIG(1):ind.USIG(2),:);
usigDemod = wlanEHTDemodulate(usig,"U-SIG",cfg);

Get the OFDM information that corresponds to the U-SIG field. Use this information to isolate the data subcarriers.

preEHTInfo = wlanEHTOFDMInfo("U-SIG",cfg);
usigDataSym = usigDemod(preEHTInfo.DataIndices,:);

Equalize the U-SIG data symbols.

x = wlanEHTEqualize(usigDataSym,preEHTChanEst(preEHTInfo.DataIndices,:),nVar,cfg,"U-SIG");

Recover the U-SIG bits, ensuring that the bits pass the cyclic redundancy check (CRC).

[usigBits,failCRC] = wlanUSIGBitRecover(x,nVar);
disp(failCRC)

   0   0   0   0

Update the recovery configuration object with the U-SIG bits. Display the updated object. A property value of -1 or unknown indicates an unknown or undefined property, which you can update after decoding the EHT-SIG common and user fields of the EHT SU packet.

[cfg,failInterpretation] = interpretUSIGBits(cfg,usigBits,failCRC) % This syntax does not cause an error if interpretation fails

cfg = 
  wlanEHTRecoveryConfig with properties:

                ChannelBandwidth: 'CBW320'
                      LSIGLength: 39
                 CompressionMode: 1
                       EHTSIGMCS: 0
        NumEHTSIGSymbolsSignaled: 2
                 LDPCExtraSymbol: -1
             PreFECPaddingFactor: -1
                  PEDisambiguity: -1
                   GuardInterval: -1
                      EHTLTFType: -1
                NumEHTLTFSymbols: -1
                UplinkIndication: 0
                        BSSColor: 0
                    SpatialReuse: -1
                    TXOPDuration: -1
                NumNonOFDMAUsers: -1
       NumUsersPerContentChannel: -1
         RUTotalSpaceTimeStreams: -1
                          RUSize: -1
                         RUIndex: -1
      PuncturedChannelFieldValue: 0
                           STAID: -1
                             MCS: -1
                   ChannelCoding: unknown
                     Beamforming: -1
             NumSpaceTimeStreams: -1
    SpaceTimeStreamStartingIndex: -1
                  Channelization: 1

   Read-only properties:
                        PPDUType: su
                      EHTDUPMode: 0

failInterpretation = logical
   0

Update Recovery Configuration Object with EHT-SIG Common Field Bits

Update the field indices with the new information from the U-SIG bits.

ind = wlanFieldIndices(cfg);

Demodulate the EHT-SIG field. Get the corresponding OFDM information.

ehtSig = rx(ind.EHTSIG(1):ind.EHTSIG(2),:);
ehtsigDemod = wlanEHTDemodulate(ehtSig,"EHT-SIG",cfg);
preEHTInfo = wlanEHTOFDMInfo("EHT-SIG",cfg);

Equalize the EHT-SIG data symbols.

x = wlanEHTEqualize(ehtsigDemod(preEHTInfo.DataIndices,:),preEHTChanEst(preEHTInfo.DataIndices,:), ...
    nVar,cfg,"EHT-SIG");

Recover and interpret the EHT-SIG common field bits.

[ehtsigCommonBits,failCRC,cfg] = wlanEHTSIGCommonBitRecover(x,nVar,cfg); % This syntax causes an error if interpretation fails

Update Recovery Configuration Object with EHT-SIG User Field Bits

Recover and interpret the EHT-SIG user field bits. Display the updated recovery configuration object.

[ehtsigUserBits,failCRC] = wlanEHTSIGUserBitRecover(x,nVar,cfg);
cfg = interpretEHTSIGUserBits(cfg,ehtsigUserBits,failCRC); % This syntax causes an error if interpretation fails
cfg = cfg{1};
disp(cfg)

  wlanEHTRecoveryConfig with properties:

                ChannelBandwidth: 'CBW320'
                      LSIGLength: 39
                 CompressionMode: 1
                       EHTSIGMCS: 0
        NumEHTSIGSymbolsSignaled: 2
                 LDPCExtraSymbol: 1
             PreFECPaddingFactor: 3
                  PEDisambiguity: 0
                   GuardInterval: 3.2000
                      EHTLTFType: 4
                NumEHTLTFSymbols: 1
                UplinkIndication: 0
                        BSSColor: 0
                    SpatialReuse: 0
                    TXOPDuration: -1
                NumNonOFDMAUsers: 1
       NumUsersPerContentChannel: 1
         RUTotalSpaceTimeStreams: 1
                          RUSize: 3984
                         RUIndex: 1
      PuncturedChannelFieldValue: 0
                           STAID: 0
                             MCS: 0
                   ChannelCoding: ldpc
                     Beamforming: 0
             NumSpaceTimeStreams: 1
    SpaceTimeStreamStartingIndex: 1
                  Channelization: 1

   Read-only properties:
                        PPDUType: su
                      EHTDUPMode: 0

Recover EHT-Data Field

Update the field indices with the new information from the EHT-SIG bits.

ind = wlanFieldIndices(cfg);

Demodulate the EHT-Data field and recover the bits. Verify that the recovered bits match the transmitted bits.

ehtData = rx(ind.EHTData(1):ind.EHTData(2),:);
ehtdataDemod = wlanEHTDemodulate(ehtData,"EHT-Data",cfg);
infoData = wlanEHTOFDMInfo("EHT-Data",cfg);
rxDataSym = ehtdataDemod(infoData.DataIndices,:,:);
dataBits = wlanEHTDataBitRecover(rxDataSym,nVar,cfg);
isequal(bits,dataBits)

ans = logical
   1

Input Arguments

sym — Demodulated and equalized EHT-SIG symbols

complex-valued matrix

Demodulated and equalized EHT-SIG symbols, specified as a complex-valued matrix. The size of the matrix is N_sd-by-N_sym, where N_sd is the number of data subcarriers in the EHT-SIG field. N_sd depends on the PPDU type and channel bandwidth.

• For non-OFDMA transmissions, N_sd is equal to 52 for a 20 MHz channel and 104 for all other bandwidths.

• For OFDMA transmissions, N_sd depends on the channel bandwidth.

  Channel Bandwidth	Nsd
  20 MHz	52
  40 MHz and 80 MHz	104
  160 MHz	208
  320 MHz	416

N_sym is the number of EHT-SIG field symbols.

Data Types: single | double
Complex Number Support: Yes

nVar — Noise variance estimate

nonnegative scalar

Noise variance estimate, specified as a nonnegative scalar.

Data Types: single | double

cfg — EHT MU transmission parameters

wlanEHTRecoveryConfig object

EHT MU transmission parameters, specified as a wlanEHTRecoveryConfig object.

csi — Channel state information

real-valued column vector

Channel state information, specified as a real-valued column vector of length N_sd, where N_sd is the number of data subcarriers in the EHT-SIG field.

Data Types: single | double

Output Arguments

bits — Recovered EHT-SIG user field bits

binary-valued matrix

Recovered EHT-SIG user field bits, returned as a binary-valued matrix. The size of the matrix is 22-by-NumUsers. The meaning of NumUsers depends on the configuration.

• For an OFDMA configuration where the same users are signaled in each 80 MHz subblock, NumUsers is the number of users in a subblock.

• For all other configurations, NumUsers is the total number of users in the transmission.

Data Types: int8

failCRC — CRC result

logical-valued row vector

Cyclic redundancy check (CRC) result, returned as a logical-valued row vector. The length of the row vector is NumUsers, which depends on the configuration as detailed in the bits output description. A value of 1 in the kth position indicates that the kth user's bits failed the CRC.

Data Types: logical

cfgUpdated — Updated EHT transmission parameters

cell array of wlanEHTRecoveryConfig objects

Updated EHT transmission parameters, returned as a cell array of wlanEHTRecoveryConfig objects. There is one object for each user who passes the CRC. The function updates the properties of these objects in accordance with the recovered EHT-SIG user field bits.

The function updates different properties of the recovery object depending on the PPDU type. If the PPDU type is MU-MIMO, the function updates these properties:

• STAID

• MCS

• ChannelCoding

• NumSpaceTimeStreams

Otherwise, the function updates these properties:

• STAID

• MCS

• ChannelCoding

• NumSpaceTimeStreams

• Beamforming

References

[1] IEEE P802.11be/D5.0. “Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications. Amendment 8: Enhancements for Extremely High Throughput (EHT).” Draft Standard for Information Technology — Telecommunications and Information Exchange between Systems — Local and Metropolitan Area Networks — Specific Requirements.

Extended Capabilities

C/C++ Code Generation
Generate C and C++ code using MATLAB® Coder™.

Version History

Introduced in R2023b

R2024b: Generate C/C++ code for 802.11be blind recovery

When you use the wlanEHTSIGUserBitRecover function for 802.11be blind recovery, you can now generate C and C++ code using MATLAB^® Coder™.

R2024a: OFDMA support

You can now blindly recover the transmission parameters of OFDMA configurations.