## Translational Measurements

### Translation Sensing Overview

You can measure frame translation in different coordinate systems. These include Cartesian, cylindrical, and spherical systems. The different coordinate systems are available through the Transform Sensor block and, to a limited extent, through the Joint blocks. The choice of coordinate system depends on the model. Select the coordinate system that is most convenient for your application.

### Measuring Translation

Translation is a relative quantity. The translation of one frame is meaningful only with respect to another frame. As such, blocks with translation sensing capability require two frames to make a measurement: measured and reference frames. In these blocks, the follower frame port identifies the measured frame; the base frame port identifies the reference frame of the measurement.

Some measurements are common to multiple coordinate systems. One example
is the Z-coordinate, which exists in both Cartesian and cylindrical systems.
In the Transform Sensor dialog box, coordinates that make up more than one
coordinate system appear only once. Selecting **Z** outputs
translation along the Z-axis in both Cartesian and cylindrical coordinate
systems.

Other measurements are different but share the same name. For example, radius is a coordinate in both spherical and cylindrical systems. The spherical radius is different from the cylindrical radius: the former is the distance between two frame origins; the latter is the distance between one frame origin and a frame Z-axis.

To differentiate between the two radial coordinates, Simscape™ Multibody™ uses the following convention:

Radius — Cylindrical radial coordinate

Distance — Spherical radial coordinate

### Cartesian Measurements

The Cartesian coordinate system uses three linear coordinates—X, Y,
and Z—corresponding to three mutually orthogonal axes. Cartesian
translation measurements have units of distance, with meter being the
default. You can use the PS-Simulink
Converter block to select a different physical unit when
interfacing with Simulink^{®} blocks.

#### Transform Sensor

You can select any of the Cartesian axes in the Transform Sensor for translation sensing. This is true even if translation is constrained along any of the Cartesian axes. Selecting the Cartesian axes exposes physical signal ports x, y, and z, respectively.

#### Joints

With joint blocks, you can sense translation along each prismatic
primitive axis. Selecting a sensing parameter from a prismatic primitive
menu exposes the corresponding physical signal port. For example, if you
select **Position** from the **Z Prismatic
Primitive (Pz)** of a Cartesian Joint block, the block
exposes physical signal port z.

### Cylindrical Measurements

The cylindrical coordinate system uses one angular and two linear coordinates. The linear coordinates are the cylinder radius, R, and length, Z. The angular coordinate is the azimuth, ϕ, about the length axis. Linear coordinates have units of distance, with meter being the default. The angular coordinate has units of angle, with radian being the default. You can use the PS-Simulink Converter block to select a different physical unit when interfacing with Simulink blocks.

#### Transform Sensor

Only the Transform Sensor block can sense frame translation in
cylindrical coordinates. In the dialog box of this block, you can select
one or more cylindrical coordinates to measure. The cylindrical
coordinates are named **Z**,
**Radius**, and **Azimuth**.
Selecting the cylindrical coordinates exposes physical signal ports z,
rad, and azm, respectively.

**Note**

**Z** belongs to both Cartesian and cylindrical
systems.

### Spherical Measurements

The spherical coordinate system uses two angular coordinates and one linear coordinate. The linear coordinate is the spherical radius, R. The angular coordinates are the azimuth, ϕ, and inclination, θ. The linear coordinate has units of distance, with meter being the default. The angular coordinates have units of angle, with radian being the default. You can use the PS-Simulink Converter block to select a different physical unit when interfacing with Simulink blocks.

#### Transform Sensor

Only the Transform Sensor block can sense frame translation in
spherical coordinates. In the dialog box of this block, you can select
one or more spherical coordinates to measure. The spherical coordinates
are named **Azimuth**, **Distance**,
and **Inclination**. Selecting the spherical
coordinates exposes physical signal ports azm, dst, and inc,
respectively.

**Note**

**Azimuth** belongs to both cylindrical and
spherical systems. **Distance** is the spherical
radius.